Signal Meters
Detect, measure, and monitor impulses of electromagnetic radiation.
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Conditioners
-
product
Full Band Noise Figure and Gain Test Extenders
STG-06-S1
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC serie...show more -
product
DIGITAL SATELLITE METER
1650S
The optimal satellite signal meter to test and measure both analog/digital signals(DVB-S, DSS). Especially, these models give users the capacity to measure 'C/N' very easily and correctly, which are very important measurement factors for the satellite broadcasting signal.
-
product
Analog Transmission
A pair of AHD (Analog HD) CCTV video signal transmisson units, it can send AHD video and DC power through one coaxial cable simulaneously. The distance between Sender and Viewer can be up to 800 meters.
-
product
Test Equipment
Our Trans-Guard DCVBD meter provides a 1kV @ 1mA test signal for direct measurement of the DC breakdown voltage of a variety of transient protection devices/products to help identify protection products that may be defective or damaged.
-
product
Programmable DC Power Supply
IT6100 Series
IT6100 series assure you accurate measurements with 0.1mV/0.1mA high resolution and high accuracy. With high-speed List mode output and voltage rise speed up to 20ms, it can independently edit and perform the default voltage waveform to meet the high-speed test needs. IT6100 series has built-in 5 1/2 digital voltmeter and milliohm meter, which can measure additional signals. IT6100 series supports SCPI communication protocol, GPIB/USB/RS232 interfaces are optional for customers.
-
product
Rope Tension Meter
RTM
The PIAB RTM Rope Tension Meter is very simple and handy to use. Simply hold and “clip” it to the rope to be tested and use the large hand screw to deflect the rope to a fixed angle. The resultant force will affect the load cell and measure the tension in the wire rope. The resultant signal is digitally processed and displayed in a selected pre programmed graduation. The PIAB RTM 20D can be graduated in kN, klbs or in ton.
-
product
Telemetry
Single channel system, offering wireless transfer of a single analogue signal, either 4-20mA or DC voltage. Mixed signal radio telemetry solution. Analogue I/O: 2x 2-40mA or DC Voltage. Digital I/O: 2x volt free or optional pulse counting required. Multi-channel radio telemetry system, 4 Analogue and 8 digital inputs. Significant signal connectivity and data transfer in a standard package.12 I/O channels allow greater signal monitoring capability SENSOR LINK Compact wireless telemetry link for any strain gauge sensor or RTD. Transmissions distance 1 to 300 meters. Licence free radio operation.16 bit ADC resolution.
-
product
Conducted Immunity Test System
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
product
Satellite FinderSatlink
WS-6903
Jointron(Quanzhou)Industry Co.,Limited
We're one ORIGINAL professional manufacturer of satellite and Terrestrial TV equipments and accessories.Here we'd like to get in touch with importers, distributors, retailers throughout the world. Since 2003, we have been exporting all kinds of satellite receivers and terrestrial receivers, and we carry a wide-range of the following products: 1.Satellite TV Equipments Including satellite receivers, satellite signal level meter, satellite finder(meter), HD DVB-S2 Receivers, DVB-S2 Meter with Spec...show more -
product
FieldFox Handheld Microwave Signal Analyzer, 50 GHz
N9962B
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
product
Digital Power Meter
Digital Power Meter is designed for single-phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits, the 66200 uses state-of-the-art DSP digitizing technology.
-
product
Process Controllers
Effective process control enhances the efficiency and performance of your operation. The heart of any sophisticated process is a controller that takes input from sensors and transmitters, measures process variables, and responds with output instructions to system components via relays and switches. We offer a wide range of process equipment including process controllers, temperature controllers, sensors and transmitters, signal conditioners, panel meters, and HMI devices. Plus we provide expert technical assistance to help you find the best solution for your application.
-
product
18 Inch Universal Flex Current Probe Accessory
FLIR TA74
The FLIR TA74 adds capabilities, simplifies challenges, and gives you the best readings with your existing meter. The narrow, 18-inch long flexible coil clamp and locking mechanism allows you take measurements in tight or awkward spots – ideal for multiple conductor measurements, double-wrap requirements, and deeper access. The connection is a standard banana plug and the output is a voltage signal, so it’s compatible with most DMMs and clamp meters, regardless of brand.
-
product
Batch Controller (analog input)
Same capabilities as the Laureate pulse-input batch controller, but for 0-1 mA, 4-20 mA, or 0-10 V process signals, as made possible by a built-in voltage-to-frequency (V-to-F) converter. Square root extraction is standard for use with flow meters.
-
product
Optical Power Meters
Optical power meter (OPM) is an essential fiber test instrument used for absolute optical signal measurement as well as optical fiber loss related measurement. The term usually refers to a device for testing average power in optical fiber systems. Fiber optical power meter is a tool for telecom and CATV network. This handheld optical power meter features ingenious appearance, wide range of power measurement, high accurate test precision and user automatic self-calibration function.
-
product
Optical Power Meter
TM233
TM233 Handheld OpticPower Meter(TM233-OPM ) are mainly used for continuous optical signal power measurement，Low power microprocessor is used for control，The TM233-OPM has the advantages of fully functional and reliable performance. Widely used in optical fiber construction and maintenance, optical fiber communication, optical fiber sensing, optical CATV and other fields. Instrument mould adopts advanced cold shell molding process; beautiful and durable, Instrument mould Design meets Ergonomic re...show more -
product
Low Input Bias Current Op Amps (≤100 pA)
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
product
PC-Based Time Interval Analyzer
GT658PCI
GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are display...show more -
product
Wireless HDMI Video Transport
1B-HDMI-W-TX/RX
QuestTel''s long range wireless HDMI Transmitter/Receiver kit fully compliant with HDCP, extends high definition audio and video to any HDTV display up to 650 feet (up to 200 meters). It supports HD resolutions up to 1080p. Wirelessly transmit the HDMI signal to any HDTV over the AIR, it also supports IR remote control function to control source device content from long distance.
-
product
PXI-6233, 16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module
779620-01
16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6233 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements...show more -
product
Multifunctional Meter
CPM-10
Chuan Sheng Electronics Co., Ltd.
CPM-10 Multifunction Power meter measure single phase 2 wire ,single phase 3 wire, three phase 3 Wire and 3 Phase 4 wire systems with high accuracy measurement for parameters such as voltage, current ,active power, reactive power, apparent power, power factor ,frequency, effective energy (V,A,W,Watt-Hr,Var,Var-Hr,VA,PF,Hz), having LED display and standard communication RTU Modbus RS485..Optional functions 1 set relay output,1 analogue,1 RS485 (ModbusRTU Mode) or 1 pulse output. Most suitable for power management,remote input /output, alarm and remote signal control uses needs.Case depth 120mm only, easy panel mounting installation
-
product
Ethernet Flying Lead
Qualified 100m Subsea Ethernet jumpers designed for data transmission and real-time situational awareness and monitoring. The typical Ethernet harness system consists of wet-mateable, Nautilus connectors, Nautilus penetrators, and pressure balanced, oil-filled (PBOF) hose conduits. Internally, the Ethernet signals are transmitted over custom Ethernet cabling sealed to seawater ingress by two independent barriers. Seven and 12-way configurations are available. Subsea connection of the harnesses may be accomplished by ROV, Diver-Mate or Stab-Plate applications. For Ethernet needs above 100 meters, see Extended Ethernet Flying Leads.
-
product
Energy Meter
The energy meters were specially developed for measuring energy on board electric traction vehicles. You can measure both the DC and the AC signals of any existing traction power supply system (1.5kV DC, 3kV DC, 15kV / 16.7 Hz, 25kV / 50 Hz). In addition, they are also suitable for multi-system locomotives with more than one electrification system.
-
product
Three Phase Power Meter
929A
Model 929A Three Phase Power Meter is an economical alternative to both the Model 931A Power System Analyzer and the Model 930A Three Phase Power Analyzer when serial communication, dc voltage measurement, transducer calibration and timer features are not required. The Model 929A has the same ac accuracy as the Model 931A with PowerDSA™ Digital Signal Analysis, and is a complete diagnostic tool for use in the substation and industrial power environment.
-
product
Portable Hand Held Load Cell Indicator
MODEL SSI
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a...show more -
product
Party Line Intercom Conversion
COMMS Series
The stand-alone COMMS 300 and the OG-COMMS openGear® units provide a means to interface between two channels of 2-wire party-line intercom audio and two channels of 4-Wire analog line-level signals. The unit is capable of performing auto nulling for each channel with the push of a button. In addition, each of the 4-Wire input and output channel levels are monitored and displayed on easy to understand front panel VU meters.
-
product
Low Frequency Vibration Signal Conditioner
A compact Signal Amplifier to make optimal signal processing being connected with the Servo type Accelerometers. It is used for Vibration Acceleration Measurement, Waveform Observation, for various Analysis in combination with the AC Voltage Meter, Oscilloscope, FFT Analyzer respectively. Furthermore, Voltage signals from the Microphones or Sound Level Meters can be output to the instruments like Recorders along with the Vibration Signals.
-
product
10 MHz To 67 GHz LAN Wide Dynamic Range Peak And Average Power Sensor
L2067XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the in...show more -
product
Instrumentation And Signal Conditioners Products
Stellar Technology offers a full line of readout meters, in-line amplifiers and signal conditioners to complement our broad variety of pressure, load/force/torque, displacement, and temperature sensors. If you’re in need of reliable signal conditioners for your essential operations, our diverse options can provide a solution. Read on to discover all that Stellar Technology can offer your company.
